Shrimp Pond Paddle Wheel Aerator Water Wheel Aerator Paddle Wheel Aerator
The process of oxygen dissolving into water is not an easy one, as water can only hold a limited amount of oxygen compared to the same volume of air. Although atmospheric oxygen can dissolve into water naturally, this process is very slow and only occurs where the atmosphere and water interact. To increase the rate of oxygen transfer, it is essential to increase the area where the atmosphere and water are interacting by agitating the water. This agitation can come naturally in the form of wave-action from wind. When wind creates waves, the surface area of the water increases, which in turn increases the rate of oxygen transfer into the water.
| Name | Quantity | Material | Remark |
| Brushless motor | 1 pcs | copper wire motor | DC48V 1000W |
| L shelf | 2 pcs | 304 Stainless Steel | |
| Pipe shaft | 2 pcs | 304 Stainless Steel | 800mm Length |
| Paddle Wheel | 4 pcs | Nylon | |
| Float | 6 pcs | HDPE | 1750mm Length |
| Connector | 2 pcs | Rubber | |
| Bearing bracket | 2 pcs | Nylon | |
| Power Distribution Box | 1 pcs | circuit breaker
solar controller
DC power supply | |
| Battery | 4 pcs | | 45AH*4 |
| Solar Panel | 2 pcs | | 250W*2 |
Furthermore, the energy stored in waves that are released when they splash into the bank or hard surfaces creates small areas of turbulence below the surface, which helps transport oxygen deeper into the water. To agitate and oxygenate large volumes of water, aerators are specifically designed while circulators are designed to propel large volumes of water. Some models combine aeration and circulation simultaneously.
However, choosing the best aerator/circulator for your situation depends on several factors such as your needs, the physical characteristics of your pond (especially depth), your budget, aesthetic preferences, and more. The appropriate size and location of aerators also vary greatly from pond to pond. In general, a typical fishing pond can be sufficiently aerated with 0.5 to 1.0 HP per surface acre.
Since several variables come into play when selecting an aerator, it is best to contact the aerator manufacturer for guidance and sizing estimates. A partial list of aerator providers is included at the bottom of this page. For more detailed explanations of dissolved oxygen dynamics, aerator efficiency, and other considerations, refer to the Additional Resources linked at the bottom of this page.
In summary, oxygen transfer into water is a slow process that requires agitation to increase its rate. Aerators and circulators are designed to agitate and oxygenate large volumes of water while propelling them respectively. The best aerator/circulator for your situation depends on several factors such as your needs, budget, and physical characteristics of your pond. It is best to contact the aerator manufacturer for guidance and sizing estimates due to several variables that come into play when selecting an aerator.
Features:
1) Actual-bevel gears are used instead of worm gears, thereby economizing energy with high efficiency, and saving over 20% electric energy over traditional models
2) The accrual-bevel gear is made of chromium-manganese-titanium with carbon-nitride surface treatment. This ensures long usage life spans and high rigidity
3) A mechanical seal is available to prevent oil leakage
4) Inside protectors are available to prevent the motor accidentally burning out
5) PE floats, nylon impellers, and stainless steel shafts and frames are available
6) Our paddle wheel aerators are greatly improved and produced according to the newest international technologies. Adopting whole plastic floats, these aerators have stainless steel transmission shafts and frames
7) In April 2000, these products were examined by the China Fishery Machinery Instruments Equality Supervision Center. All 9 models were evaluated as reaching the SC/T6017-1999 standard
8) With oxygen transfer rates of 2.59kg (O2)/h, 36.3% higher than the standard, power efficiency is 1.71kg (O2)/kWh, 36.8% higher
than the standard
High oxygenation performance :
1 High quality motor expertise design for aquaculture industry
2 Low friction gear reducer with low resistance to decrease energy losses
3 Sturdy stainless steel Frame ensure without any deformation and high durability
4 High performance impeller, replaceable paddle,low maintain cost
5 HDPE float resist impact, acid-alkalinity and sun exposure, one piece blow molded
Working Principle
Powerful features making wave with bottom surface accelerated the exchange of oxygen-rich water to fully utilize photosynthesis of algae to consume organic residues, can save feed, but also purify water, to avoid NH3 and nitrite and other harmful substances. Pond surface waves more easily dissovled oxygen rate,adjust the upper and lower temperature, more conducive to water modulation.
FAQ
Q1. Are you a manufacturer or trading company?
A: We are a manufacturer.
Q2. What's your company's main products?
A: Our company is specialized in kinds of aerators for fish pond and shrimp pond, such as paddlewheel aerator.
Q3. What's the MOQ for your production?
A: NO MOQ.
Q4. What's the lead time?
Usually about 15days-20days, if large quantity, will check the production line and arrange the schedule.
Q5. What's your payment term?
A: 30% T/T in advance, the rest pay off before delivery.
Q6. Where is your loading port?
A: Ningbo, or else port in China as your requirements.
Product Tags:
|
|
0.75KW Shrimp Farming Aerator Water Wheel Aerator For Prawn Pond Paddle Wheel Images
|
